Oil Filters

SynLube™ Lube−4−Life®

100% SYNTHETIC MEDIA SUPER FILTERS
Semi-Permanent replacement for Cellulose media Oil Filters

Description

The SynLube™ Lube−4−Life® Oil Filters may look the same as the conventional Oil Filters that they replace, but the similarity ends there.
The SynLube™ Lube−4−Life® Oil Filters offer superior performance well beyond that of conventional oil filters, including:

• Cleaner Oil
  • Substantial improvement in multiple-pass filter efficiency
    (95% vs. 80% for conventional filters)
    is achieved through the use of synthetic MicroGlass fibers in the filter media
• Wire Backing
  • protects the filter media from tears and provides uniform spaces between each pleat for improved oil flow.
• Improved housing to base crimp
  • reduces potential for Filter Failure due to Pressure Build-up
  • outperforms conventional filters by 2.5 to 1
    in hydrostatic pressure testing (steadily increasing pressures)
• Thicker gauge housing
  • reduces potential for Filter Failure Due to Repeated Pressure Surges at Start-up
  • outperforms conventional filters by 3 to 1
    in cyclic pressure impulse testing (SAE J806, 0-100 PSI @ 0.5 Hz)
• Non-stick Gasket
  • Permits easier Filter Removal after use

Key Benefits

• Longer Service Life
  • from 1 Year or 15,000 miles**
  • to up to 5 Years or 50,000 miles**
  • 2 Years or 25,000 miles
    - or -
  • 3 Year or 36,000 miles
    is typical for most applications**
    • ** Based on filter size relative to typical oil flow (volume per minute) at operating temperature
• Greater Filtration Capacity
  • Traps up to 5 times more contaminants*
• Lower Oil Flow Resistance
  • Improves Filtered Oil Flow by up to 80% @ 30°F (-1°C)
• Greater Filtering Efficiency
  • Traps particles that are up to 4 times smaller*
    (10 microns vs. 40 microns)
    

* when compared to Conventional Cellulose media Oil Filters,
   Test Results based on SAE J 1858 Testing Procedure

Other Benefits

The SynLube™ Lube−4−Life® Oil Filters outperform conventional filters in several key tests:

• Single pass efficiency (SAE J806) of 98% vs. an 85% average for conventional filters.
• Multiple pass efficiency (SAE J806) of 95% vs. an 80% average for conventional filters.
• Hydrostatic burst strength of 600 PSI vs. 240 PSI average for conventional filters.
• In pressure impulse fatigue testing (SAE J806, 0-220 PSI @ 0.5 Hz),
  over 25,000 cycles vs. less than 1,000 cycles to failure for conventional filters.
• Synthetic MicroGlass filter fibers create smaller, more consistently sized openings,
  which improves oil flow and traps smaller (8 to 10 micron) contaminants
• All metal end cap construction along with wire backing of synthetic filter media and steel coil spring loading of the filter element provides for "grounded" construction which eliminates "static build-up".

Filtration

SynLube™ Lube−4−Life® Oil Filter technology uses special synthetic glass microfibers that are about 10 times smaller than conventional cellulose filter fibers (shown below). This allows a full flow oil filter to have following performance:

• 99% particle removal that are 10 micron in size
• 98% particle removal that are 7 micron in size
• 95% particle removal that are 5 micron in size

Typical Cellulose Filter Media - SynLube™ MicroGlass™ Media

Most manufacturers that make low cost filters do not disclose or advertise any data on their products filtration range or efficiency, but research done by General Motors indicates following:

• Typical low cost oil filter will remove about 40% of particles in 8 to 10 micron range
• Typical OEM oil filter will remove about 72% of particles in 8 to 10 micron range

Want to Know MORE ?

Just Click the link(s) below

• ALL ABOUT OIL FILTERS
• HOW OIL FILTERS WORK
• FILTER MEDIA
• FILTER MAGNETS

Pricing

Note: SEE PRICE LIST for current pricing (or Click link in HEADER)

Just Click the link button below (if visible in your browser)

CROSS-REFERENCE

Click the Oil Filter Code in the THIRD COLUM of PRICE LIST for pop-up page listing all known filters that cross-reference to that product and also to see product technical details.

Note:

SynLube™ Lube−4−Life® Oil Filters are made in USA for SynLube Incorporated by several different manufacturers and are made exclusively to our specifications.

SynLube Incorporated DOES NOT manufacture any Oil Filters.

SynLube Incorporated only carries Oil Filters in the inventory for ease of ordering by our cusomters and so that they can be assured that only PREMIUM quality Oil Filters are used in their vehicles along with SynLube™ Lube−4−Life® Motor Oil.